The ThinAir® Hand Dryer is a high-efficiency model that is surface-mounted and ADAcompliant. ThinAir dries hands in 15 seconds*, uses 950 watts or less (as low as 300 watts) and has a slimmer profile to meet ADA compliance standards. The ThinAir Hand Dryer features adjustable speed and sound control, variable heat settings and a washable pre-filter.
  • 15 Second Dry Time*
  • Wattage: 950 Watts (Heat On) – 300 Watts (Heat Off)
  • Meets 4” ADA protrusion guidelines to accommodate the visually impaired
  • Adjustable Speed and Sound Controller
  • Variable Heat – High, Medium, Low and Off
  • Washable Pre-Filter
  • 5-Year Limited Warranty




Width 9 5⁄32″ (233 mm) Height 13 15⁄16″ (354 mm) Depth 4″ (102 mm)

TA-ABS: 8 lbs. (3.6 kgs.)

A. All covers will be fastened to a base plate by one chrome plated tamper-proof bolt.

The cover shall be composed of:
ABS – White polymer with SanaFor™ antimicrobial additive

B.Base plate shall be equipped with (3) 7/8″ (22 mm) diameter knockouts,
one of which is located on the right side and suitable for use with
surface conduit.

C. All internal parts shall be coated according to Underwriters’
Laboratories, Inc. requirements

D. Entire mechanism shall be internally grounded, per UL requirements.

E.Accessories (optional)
MICROBAN® Antimicrobial Wall Guards: 89W (White), 89B (Black), 89S (Stainless)

A. Motor shall be a thermally protected, series commutated, through-flow discharge vacuum motor/blower (~½ hp / high-30,000 rpm, low-20,000 rpm) which provides air velocity of up to 16,000 LFM (linear feet per minute) at the air outlet.

B. Heating element (550 W) is constructed of Nichrome wire and mounted inside the blower housing behind air baffle, thereby being vandal resistant. It shall be protected by an automatic resetting thermostat, which shall open whenever air flow is cut off and shall close when flow of air is resumed. It shall produce an air temperature of up to 141°F (61°C) at a 72°F (22°C) ambient room temperature at the outlet and 101°F (38°C) at the hands (4 inches [102 mm] below air outlet).

C. Control assembly is activated by an infrared optical sensor located next to the air outlet. The dryer shall operate as long as hands are under the air outlet. Control includes a speed and sound control mechanism, variable heat control with High, Medium, Low and Off settings and a filter sensor which is activated should the filter become clogged. There is a 35-second lockout feature if hands are not removed. Sensor equipped with externally visible Red LED light that can flash error codes to assist in troubleshooting.

The dryer shall be guaranteed to be free from defects for a period of five (5) years. Warranty shall include labor performed at factory as well as the repair or exchange of defective parts, at manufacturer’s option.
One dryer for every two washbasins is sufficient for most applications. If restroom traffic is unusually heavy, we suggest one dryer per washbasin in small installations and two dryers for every three washbasins in larger installations. When a 54″ washfountain is used, we suggest four to five dryers.


Model No. Cover Finish
TA-ABS White Polymer (ABS)


Automatic Sensor Operated


Surface Mounted

ADA Compliance

ADA guidelines state that fixtures mounted above 27″ must not protrude more than 4″ from the wall.



110-120V 7-7.7A 770-915W 3-3.2A 310-370W 50/60 Hz
208-277V 3.6-4.0A 735-950W 1.5-1.9A 300-375W 50/60 Hz
230V 3.9A 890W 1.7A 375W 50 Hz


Suggested Mounting Heights

from floor to bottom of dryer:

Men 45″ (114 cm)
Women 43″ (109 cm)
Teenagers 41″ (104 cm)
Children 35″ (89 cm)
Handicapped 37″ (94 cm)
Contact Us

Want to know more or how to buy?

Contact us and we'll send you everything you need to know

Contact Us